What are your opinions about Installing A Bathtub?
Mounting a bath tub isn't specifically rocket science, however it does require strong plumbing, woodworking, as well as in some cases, tiling skills. Replacing an old bathtub with a brand-new one is also a reasonably tough project. If the old bathtub is readily accessible, the job can move immediately; if you need to open a wall surface to remove the old bathtub and position the brand-new bathtub, the task is a lot harder. In either instance, the project is within a house handyman's abilities, although you will certainly require an assistant to vacate the old tub as well as set in the brand-new one. Make certain you have certified yourself for the job and also are comfortable attempting it. As opposed to hiring a professional to take over a halfway-completed task, it is far better to think about employing one prior to you start. Opportunities are you might require a specialist plumber to make tube links.
This post will help you install a brand-new bath tub in your washroom if you have currently gotten a new bathtub as well as do not require to alter the arrangement of your previous water supply pipelines.
Your devices as well as product checklist need to consist of the following:
Getting ready for the Installment
First of all, the sustaining structure provided with the bathroom needs to be fitted (if required) according to the producer's guidelines. Next off, fit the faucets or mixer to the tub. When fitting the tap block, it is necessary to make certain that if the tap comes with a plastic washing machine, it is fitted in between the bathroom and the faucets. On a plastic bathroom, it is also reasonable to fit a sustaining plate under the faucets system to stop stress on the bath tub.
Fit the adaptable faucet ports to the bottom of the two taps utilizing 2 nuts and also olives (occasionally supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet via the hole in the bath. Utilize the nut provided by the producer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which must be fitted inside the bathroom. See to it you make use of all of the provided washers.
Connect the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect all-time low of the overflow tube in a similar manner.The bath ought to now prepare to be fitted in its final placement.
Removing Old Taps
If you need to replace old faucets with new ones as a part of your setup, after that the first thing you need to do is disconnect the water system. After doing so, activate the faucets to drain pipes any water remaining in the system. The procedure of getting rid of the existing faucets can be fairly problematic because of the restricted gain access to that is usually the instance.
Make use of a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipelines to the taps. Have a cloth all set for the continuing to be water that will certainly originate from the pipes. Once the supply pipelines have been gotten rid of, utilize the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the single faucets from turning throughout this procedure. Once the taps have actually been gotten rid of, the holes in the bath/basin will have to be cleansed of any type of old securing substance.
Prior to going on to fit the brand-new faucets, compare the pipe links on the old faucets to the new faucets. If the old taps are longer than the brand-new taps, then a shank adapter is needed for the brand-new faucets to fit.
Installing the Tub
Making use of the two wooden boards under its feet, position the bath tub in the called for placement. The wood boards are practical in equally spreading the weight of the tub over the area of the boards rather than concentrating all the weight onto four small points.
The next objective is to make certain that the bath tub is leveled all round. This can be attained by inspecting the spirit level as well as adjusting the feet on the tub up until the spirit level reviews degree.
To mount faucets, fit the bottom of the furthest adaptable tap adapter to the suitable supply pipe by making a compression sign up with; then do the same for the various other tap.
Switch on the water and examine all joints and brand-new pipework for leaks and also tighten them if required. Load the tub as well as additionally check the overflow electrical outlet and the typical outlet for leakages.
Ultimately, fix the bath paneling as described in the maker's instruction manual. Tiling and also securing around the bathtub must wait up until the tub has actually been used at the very least once as this will certainly settle it into its final placement.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic port to avoid damage to the thread. One end of the port fits on the plastic tail of the tap and the other end provides a connection to the existing supply pipes.
If you require to fit a monobloc, after that you will require reducing couplers, which connects the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next, position the faucet in the placing hole in the bath/basin guaranteeing that the washers remain in area in between the tap and the sink. Safeguard the tap in position with the maker offered backnut. As soon as the tap is securely in position, the supply pipes can be attached to the tails of the taps. The faucets can either be linked by utilizing corrugated copper piping or with typical faucet connectors. The former type needs to be linked to the faucet ends first, tightening up only by hand. The supply pipes can later on be linked to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Bathtub
In the area where the bath meets the tile, it is required to seal the accompanies a silicone rubber caulking. This is essential as the installation can move enough to break a stiff seal, creating the water to penetrate the wall surface in between the bathroom and also the tiling, bring about complications with wetness and also feasible leakages to the ceiling listed below.
You can pick from a variety of coloured sealants to assimilate your components as well as installations. They are offered in tubes as well as cartridges, and can sealing gaps up to a size of 3mm (1/8 inch). If you have a larger space to load, you can load it with twists of soaked newspaper or soft rope. Bear in mind to constantly fill the bath tub with water before securing, to enable the activity experienced when the bathtub is in usage. The sealer can split rather very early if you do not take into consideration this movement prior to securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are additionally quickly available on the marketplace. It is recommended to fit the tiles using waterproof or water-proof sticky and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As an avid person who reads about How to Install a Bathtub, I think sharing that piece of writing was a smart idea. Enjoyed our posting? Please share it. Help others check it out. Thanks a bunch for your time. Come back soon.
Get Quote Now